Endura Flap™ Retainer Clip

SKU# 91CO20

The Patio Pacific Endura Flap Retainer Clip

View Warranty

Stock No: 91CO20

Availability: In stock

Price From: $20
Loading options please wait..
What size do I need?
Price From: $20
Endura Flap™ Retainer Clip
New plastic retainer bottom

Hover over image to zoom

The Patio Pacific Endura Flap Retainer Clip

Flap SizeFlap DimensionRough Cut OutOutside Frame Dimension
Small6" w x 11" h8 3/8" w x 15" h9 7/16" w x 15 3/4" h
Medium8 " w x 15" h10 1/2" w x 19" h11 1/2" w x 20" h
Large10" w x 19" h12 1/2" w x 23" h13 9/16" w x 23 5/8" h
Extra Large12" w x 23" h14 5/8" w x 27 1/8" h15 5/8" w x 28" h

The Patio Pacific Endura Flap Retainer Clip

This clip locks the two parts of the Patio Pacific Endura Flap together. Normally they don't need to be replaced.

This is not a magnetic strip for the bottom of the dog flap, however it will come with the magnets needed to insert into the bottom of the Endura Flap.

These parts are not interchangeable with other manufacturers. If you do not have an Endura Flap than this magnetic bar for dog door and cat door installation will not work.

Customer Reviews

Set Direction
  • A bit tricky to take off review by Jim
    5 4 A bit tricky to take off

    It was sort of difficult to pry off the old retainer bottom from my flap but this new one fits and works fine. I recommend using a rubber mallet to help get it back into place

    (Posted on 2/21/2018)

  • Parts review by buddy
    5 3 Parts

    Wish the magnets would be included too, but they aren't. When this comes off the magnets fall out of the flap.

    (Posted on 12/19/2017)

  • Fits perfectly! review by Stephanie
    5 4 Fits perfectly!

    I got this after my dog ripped the old one. The installation was a bit tricky at first but the customer service staff sent over a video on how to do this.

    (Posted on 12/6/2017)

  • Good Replacement review by Scott
    5 5 Good Replacement

    This part is necessary to hold the magnets on the bottom of the two piece flap. It fits the flap perfectly since it is an original piece from the manufacturer.

    (Posted on 12/5/2017)

  • Replacing was a little tough review by Robin T
    5 4 Replacing was a little tough

    Trying to take out the old one was harder than I thought especially since putting the new one was pretty simple. With a couple twists and yanks it worked out.

    (Posted on 11/29/2017)

Manufacturer Endura Flap

Endura Flap Retainer Bottom Installation Instructions

Included Materials: 1 Endura Flap Retainer Bottom

Mallet (optional)
Flathead screwdriver or other flat tool (optional)

Installation Steps:

1. Order the correct replacement size

2. Remove the old retainer bottom if still attached:

- This can usually be done by bending the retainer outwards so that you can slip your fingers underneath it. At that point, pull and twist until the retainer comes off of the flap. Warning: The magnets underneath will likely fall out

- If it is too difficult to do by hand, you can use a flathead screwdriver or any other flat, thin tool to slide between the retainer and the main flap body and use it to lift the retainer off of the extrusions holding it on. Take care not to damage the main flap body

3. Ensure that the magnets are still in place or replace the magnets

4. Position the new retainer bottom so that the cutouts on the retainer are roughly in line with the extrusions on the flap body

5. Push the retainer bottom onto the flap and over the extrusions:

- This can be done by hand, but it is easier to use a mallet to tap the retainer bottom into place. Ensure that the edge of the main flap body doesn’t get caught in the cutouts of the retainer, as it will keep the retainer from sliding on. If it does, you can push them inside the retainer by hand.

- Regardless of whether done by hand or by mallet, the retainer bottom cutouts will likely be slightly offset from the flap body extrusions. Push and pull the retainer bottom side-to-side until you can feel each of the corners of the extrusions sticking out of the cutouts. This ensures that the new retainer will not come off.

Write Your Own Review

You're reviewing: Endura Flap™ Retainer Clip

  • 1 star
    2 stars
    3 stars
    4 stars
    5 stars

* Required Fields

Patio Pacific Inc Endura Flap™ Pet Door Warranty

To the original purchaser, Patio Pacific Inc warrants this product and all of its component parts to be free of defects in materials or workmanship for a period of 15 years from the date of delivery to the customer.

Endura Flap™ assemblies are warranted for a period of 15 years. Endura Flap™ assemblies employed in commercial kennels are warranted for a period of 3 years.

Damage caused by accident, improper installation, abuse or normal wear, including damage by pets or glass breakage, is specifically excluded from this warranty.

Defective materials returned to Patio Pacific Inc, together with proof of purchase, will be repaired or replaced and returned to the customer free of charge.

Pet doors of other manufacturers installed in Patio Pacific products are covered by the warranty of the other manufacturer and not by Patio Pacific Inc.